How to Fix The Drooping Ceiling Fan Blades
Ceiling fan blades droop when the fan is too heavy
If your ceiling fan blades droop, it's usually because the fan is too heavy. The weight of an individual blade can vary from 28 ounces to nearly 100 ounces depending on the length and size of the blade. If you have a large room with high ceilings, you may need heavier materials to support your heavy-duty fans.Ceiling fans are typically made up of four distinct parts: the motor housing, which connects directly to an electrical outlet; a down rod (also called a drop rod); a bracket that connects directly to the ceiling; and finally, blades that attach directly to this bracket. The weight of each component plays an important role in how they function together as well as their overall sturdiness.
If a fan is too heavy, it will put pressure on the ceiling fan mounting bracket, causing the blades to droop slightly
- This can be caused by one or more of the following.
- The weight of the fan blades.
- The weight of the motor.
- The weight of the mounting bracket.
The more you weigh, and/or how far away your ceiling is from its original position, will also affect how much your ceiling fan will droop over time
Step 1 - Check For A Problem With The Hanger Bracket
It is important to first determine if the problem lies with the hanger bracket, or the fan blade itself. The following are some of the most common causes:- The fan is too heavy
- The blades are too small or large in comparison to each other
- The floor is not level
- There is a problem with one of your ceiling joists or rafters
Step 2 - Turn Off The Power To The Ceiling Fan
To safely turn off the power to a ceiling fan, you'll need to turn off the breaker for the room where your ceiling fan is located. You also may want to turn off the switch that powers your light and/or wall switches. If you're not sure if it's safe to do so, use a circuit tester to make sure there's no power going through any of these wires before proceeding.Step 3 - Locate The Screws Or Bolts That Hold The Blade To The Bracket
- Locate the screws or bolts that hold the blade to the bracket.
- Remove the blade from its bracket by loosening these screws or bolts.
Step 4 - Remove The Blade From The Bracket
After you've removed the blade from the ceiling, remove it from the bracket by unscrewing both screws on either end of the bracket. You should now have a free-floating ceiling fan blade.Now that you have all four blades off your ceiling fan and hanging freely in front of you, it's time to decide which one goes back where. If your goal is to fix a drooping blade, then simply reverse these steps and put them on in reverse order—first put up your best new-looking blade and then move onto each successive older looking one until they're all back up in place again!
Step 5 - Tighten Up Any Loose Holes In The Bracket And Blades
To tighten up the bolts, you can use a wrench. The wrench is just one of many tools that can be used to tighten up bolts. You could also use a screwdriver, or even a hammer if you prefer. If you have access to an electric drill or socket set, then that would work too!Step 6 - Reattach Your Blades To Your Brackets Securely
Now that all your blades are balanced, it's time to secure them back on their brackets. If you're using the same screws, this should be easy. If not, then double check that your new screws are long enough and that they're going into the correct holes on both sides of each blade. Once you've successfully restrung your fan, give it a test spin and make sure everything feels tight before securing any other parts (like the light kit or remote control).Follow these steps to repair your ceiling fan blades in no time.
- Calculate the distance from the tip of the first blade to the ceiling using a measuring tape. Jot down the calculated value on the blade’s masking tape.
- Here, you will need to repeat step 1 for the remaining blades. This will eventually bring each blade to the position of the first blade. Furthermore, blades lying below the ceiling fan must be bent upward for straightening the hanging. Pushing the blades upward can slightly bend the irons.
- Additionally, place a fan blade with a larger measured value in comparison to the other blades.
- Next, hold the fan motor with one hand and press the drooping tip slightly upwards with the other one.
- Ensure that all distances between fan blades are equal.
- Now, you can peel the masking tape from each blade.
- Finally, activate the ceiling fan at the wall switch. Carefully notice the motion of the blade. Now it must not be drooping anymore.
Step 7 - Reinstall Your Ceiling Fan Blades And Turn On Power
Once you've removed the fan blades, it's time to reinstall them.Make sure you turn the power back on before you start working with your ceiling fan again. This is important because if there's a lot of dust in the room and someone plugs in a vacuum cleaner, they may get shocked by an electrical shock. Also make sure that no one gets too close to the blades while they're spinning fast; they could get hurt if they were accidentally knocked over or hit by a blade!
It's also important that when you put them back into place, you don't accidentally touch any wires or disconnect anything from where it was connected before because this can lead to short circuits or other problems with electricity running through them (which might cause fires). If this does happen then call an electrician immediately so that he/she can fix any issues with wiring before anyone gets hurt!
Always wear protective gear like goggles when working around blades spinning at high speeds! You don't want any cuts on your face from falling debris either!"
You should keep all of these things in mind when you are doing this project
Before you begin, turn off the power to your ceiling fan.Use a screwdriver to remove the screws or bolts that hold the blade to the bracket.
Use a pliers to tighten up any loose holes in the bracket and blades.
To avoid this altogether, make sure you purchase a ceiling fan that has blades made from aluminum or wood
To avoid this altogether, make sure you purchase a ceiling fan that has blades made from aluminum or wood. Aluminum blades are lighter than steel and therefore easier to move around when trying to fix a droopy blade. They also tend to cost less than wood options. However, be aware that some manufacturers use laminate rather than solid wood on their products and may advertise them as such; if you have children in your home (or pets), it's best to purchase an all-wood model so as not to risk injury or damage caused by splinters.Wooden blades can be expensive compared to their aluminum counterparts, but they're durable and safe for homes with children because they aren't prone to splintering like metal ones can be; they also don't rust over time like steel does when exposed directly outdoors year after year
To fix the drooping problem, try replacing the blades with light weight blades made of aluminum or wood
The first thing you can do is replace the blades with light weight ones. Fans with aluminum or wood blades are less likely to droop because they're not as heavy, so try a ceiling fan that has these kinds of blades. Also, if you already own a ceiling fan with heavier metal blades, consider replacing them with lighter weight ones.Another way to fix this problem is by using a different style of blade altogether. If your existing fan has metal slats instead of solid paddles (this is what holds up all those other pieces), then simply replacing those slats may help solve your problem as well! You can also purchase new mounting brackets for either type of design; these will provide additional support against drooping or sagging in general because they'll hold up more weight than just one piece
Conclusion
With a little time and care, you can easily fix your own drooping ceiling fan blades. We hope this guide was helpful to you!Now that you’ve fixed your fan, all that’s left to do is sit back and enjoy the cool breeze.
And that’s all there is to it! It may have taken some time, but you now have an attractive and efficient ceiling fan.
Comments
Post a Comment